Wheel Data

Discussion in 'Bay Tech Clinic' started by Kombirod, Feb 22, 2008.

  1. Kombirod

    Kombirod New Member

    Messages:
    1,132
    Location:
    Manly, NSW
  2. syncro

    syncro Well-Known Member

    Messages:
    8,425
    Location:
    Southern Highlands
  3. 67micro

    67micro Member

    Messages:
    72
    Location:
    Monavale
    That lowlight in your profile photo looks the same as my lowlight 108_9982 - Copy.jpg
     
  4. wenmac

    wenmac Active Member

    Messages:
    521
    Location:
    Sunbury
    Can I get smoothies to fit my '75 Bay? If so, where?
     
  5. Aspro

    Aspro Well-Known Member

    Messages:
    2,279
    Location:
    Stuck in the UK
    No mate. Smoothies are wide 5 stud pattern (5x205) Your late bay is 5x112.
     
  6. Grazza7755

    Grazza7755 Active Member

    Messages:
    136
    Location:
    Palmers Island NSW
    I have 4 x Audi alloys ( no tyres) for sale $100- and 4 x alloys (reasonable to good tyres ) $100-
    IMG_2092.JPG IMG_2105.JPG IMG_2106.JPG
     
  7. wenmac

    wenmac Active Member

    Messages:
    521
    Location:
    Sunbury
    Thanks Aspro, I'll keep looking for wheels then.
     
  8. QUAMBY

    QUAMBY Member

    Messages:
    62
    Location:
    Edithvale Melbourne
    Does anyone know if a wheel with these specs will fit my bay?

    Size 16 x7
    Stud 5 x 112
    PCD 160
    Offset 36

    I had a look at the website attached to post 1 but im useless with that sort of stuff.

    Thanks in advance.
     
  9. Aspro

    Aspro Well-Known Member

    Messages:
    2,279
    Location:
    Stuck in the UK
    Slighly confusing as PCD is stud size. So what is 160 then?
     
  10. QUAMBY

    QUAMBY Member

    Messages:
    62
    Location:
    Edithvale Melbourne
    This is a screenshot from the seller of the wheels but I'm not sure it answers your question.
     

    Attached Files:

  11. AC-T3

    AC-T3 Active Member

    Messages:
    720
    Location:
    Woy Woy
  12. splitbus

    splitbus Well-Known Member

    Messages:
    3,237
    Location:
    Brisbane
    Standard offset is 39 so your ok there
    5 x 112 is right
    7 inch is the question and a problem
    I had 15 x 5 1/2 inch with 195 tyres and they where close to guard on rear
     
  13. Barry

    Barry Well-Known Member

    Messages:
    1,764
    Location:
    Abbotsford NSW
    Mine are 17" x 7" ET40
    but if it is lowered at all it "may" rub
    also depends what tyre you use.
    I run a 215 x 45 and get an "occasional" grab on the front is one wheel goes up an inclined drive way if i go in at 45 degrees
    As yours are ET36 it will be 4mm further out
    a 205 may be a better fit

    If you are not lowered then i would say no problems
     
  14. Barry

    Barry Well-Known Member

    Messages:
    1,764
    Location:
    Abbotsford NSW
    QUAMBY likes this.
  15. Grantus

    Grantus Well-Known Member

    Messages:
    13,189
    Location:
    Southern ACT
    Looks like they should be advertised as:

    Size 16 x7
    Stud 5
    PCD 160
    Offset 36
    :rolleyes:
     
    Last edited: Jul 17, 2016
    QUAMBY likes this.
  16. QUAMBY

    QUAMBY Member

    Messages:
    62
    Location:
    Edithvale Melbourne
    Thanks mate much appreciated I will keep looking!
     
  17. cbus

    cbus Well-Known Member

    Messages:
    10,273
    Location:
    sunshine coast
    Agree with Grant.
    Think seller has a missprint.

    PCD is usualy written for a bay or t3 as
    5x 112
    Being 5 studs and PCD of 112 mm

    Looks like above rim should be
    5 x 160mm

    If looking for wheels check the face for nut mounting as well.
    12 and 14 mm studs with ball face are different profile.
    They will fit but do not contact across full surface.

    Mags may require specific nuts as well.

    Also mags are usualy thicker in mounting area and you may require longer studs to comply with regulations that state that the stud must reach to outer face of nut.
     
  18. syncro

    syncro Well-Known Member

    Messages:
    8,425
    Location:
    Southern Highlands
    Yes TATA wheels are 5x160.
     
  19. Blunderbus

    Blunderbus Active Member

    Messages:
    513
    Location:
    St Helena, Melbourne .
    Thats an odd size, dont know of anything with the same PCD. Closest would be Land Rover at 165.
     
  20. AC-T3

    AC-T3 Active Member

    Messages:
    720
    Location:
    Woy Woy
    Try Ford Transit 2003+
     

Share This Page