1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

1955 sheep carrier

Discussion in 'Resto Corner' started by chuck85, Nov 9, 2013.

  1. old grey

    old grey Well-Known Member

    Messages:
    748
    Location:
    newcastle
    Feeling your Easter enthusiasm. Looks good mate, keep plodding away and it'll happen.
     
  2. chuck85

    chuck85 Member

    Messages:
    68
    Location:
    Shellharbour
    20170507_155931.jpg 20170502_101710.jpg IMG_20161111_100125.jpg Rest of body panels arrived.
    Rear all jacking points and outriggers install. Top hats repaired and ready to be welded in. Front pass side jacking point and outrigger installed and bulk head section repaired.
     
    Last edited: Oct 2, 2017
  3. chuck85

    chuck85 Member

    Messages:
    68
    Location:
    Shellharbour
    Havent had much of a chance to work on the old girl, but been slowly doing little bits here and there.
    Made up the bottom midfle of the bulk head section, still needs to be trimed to size.
    Front door where hinges bolt to were all rusted out, made some new backing plates up and also some new hinge pin/ mirror arm.
    Couldnt find correct size pipe for the centre heater tube, so made up some repair sections to suit
    Resized_20170703_231703.jpeg Resized_20170708_012246.jpeg


    Resized_20170708_012552.jpeg Resized_20170708_012543.jpeg
     
    StevieVW and David H like this.
  4. saabman

    saabman Well-Known Member

    Messages:
    4,803
    Location:
    Goulburn
    Awesome work chuck.
     
  5. OSF

    OSF Well-Known Member

    Messages:
    1,085
    Location:
    Sutherland NSW
    Looking Good. Keep it going.
     
  6. chuck85

    chuck85 Member

    Messages:
    68
    Location:
    Shellharbour
    Got abit more done today. Front floor all tacked in places. Tool chest area floor welded in, bottom of bulk head welded in place. Test fit rear floor n modified from lhd to rhd.
    Still got to clean welds up n straighten a few thimgs but getting slowly 20171001_210556.jpg 20171009_094936.jpg 20171009_132635.jpg 20171009_141928.jpg
     
    Syncro27 likes this.
  7. Squalo

    Squalo Active Member

    Messages:
    213
    Location:
    Sunshine Coast QLD
    Good to see this one still coming along :)
     
  8. 77/kombi/surfer

    77/kombi/surfer Well-Known Member

    Messages:
    1,801
    Location:
    Budgewoi N.S.W. AUSTRALIA
    Coming along real nice.
    Great metal work skills by the way.
    Cheers chuck
     
  9. chuck85

    chuck85 Member

    Messages:
    68
    Location:
    Shellharbour
    Slowly getting there.
    Been watching ur thread Chuck.its got me keen to get mine on the rd. But im still along way off.
     
    77/kombi/surfer likes this.
  10. chuck85

    chuck85 Member

    Messages:
    68
    Location:
    Shellharbour
    Most of the basic body work is done just got to finish off drives door , than highfill. Starting to assemble to see what’s missing, and hopefully get her started and drive around the block in the next few months. 45769553-DB08-48FD-AC22-E65D41D59FBF.jpeg
    Made up some tail light housings, looking at putting orange LED light between red light and housing for blinkers
    . 8451FD36-8694-4401-864D-C10E2459B3A4.jpeg 492CCA3E-30A5-4162-9182-2FCD9948178B.jpeg
    Machined up some aluminium knobs
    D3DBA59F-E21B-4598-AC63-94FBC5A8BDDC.jpeg
     
    jimbi, Barry, Wayne murray and 5 others like this.

Share This Page